2017 Popular App Control Home Automation Wifi House Automation Smart Home

Product Detail

 2017 Popular App Control Home Automation Wifi House Automation Smart Home




Gateway

The product was linked sensing system as the "hub" controller, plays various types of signals collected by the front end of each type of sensor, will be converted into WIFI signal RF transmitted to the platform with the server. Without this product, in front of the sensor can not complete its function.

Radio signal processing front-end device (PIR, Door switch, Gas detector, Smoke detector, etc.) sent a distinction between processed and transmitted to the platform with the server via the mobile phone APP pushed to the user-related information, prompts the user to make the appropriate treatment. A variety of modes can customize zones and equipment, increased user freedom.

 

PIR

- Pull out the battery insulating sheet, probe into the 1 minute warm-up state, the indicator flashes 1 second interval, waiting sensors stable.
- The preheating is finished, the detector 5 minutes before entering the test mode, 5 minutes into the usage patterns.
Test mode: When the detector detect the infrared signal, It will alarm.
Use mode: The detector to detect infrared signals every 5 minutes, before the next probe, to achieve energy saving effect.
- The detector detects infrared signals, lights flash once, to send an alarm signal alarm box, but pushed to your phone APP, it informs the user.
- Key functions: Testing. Single press the probe into the five minutes’ testing mode so that users install, test.
- Anti-pet function: Pets in front of the infrared detector movement does not trigger an alarm, to avoid false alarms caused by pets.
- Low voltage remind function: When the battery is about to run out of the detector, the detector will send a low-pressure alarm signal to the alarm box, to remind the user to replace the battery.
- Inspection function: the detector can inform the user is online.
- The tamper function: when the detector is removed or opened, it will send a tamper alarm signal that prompts the user.

 

Door switch

- Door containing the host and auxiliary machinery, are mounted on the door and door frame (window similar), both part of the installation interval should be less than 10mm, when the spacing is more than 15mm, the transmitter can lights can be.
- Pull out the battery insulating sheet detector that is working properly. When the host and auxiliary engine separated, the indicator flashes once, to send an alarm signal alarm box; master and slave unit is closed, the light blinks once, and door sensor sends a resume signal.
- Low-voltage remind function: When the battery is about to run out of the detector, the detector will send a low-pressure alarm signal to the alarm box, to remind the user to replace the battery.
- Inspection function: to inform users detectors are online.
- The tamper function: when the detector is removed or opened, it will send a tamper alarm signal that prompts the user.

 

Remote Control

Four buttons, Away, home arm, disarm and SOS emergency assistance.

 

Gas Detector

- Connected Power, detector self-test, the yellow light flashes once, the buzzer "drip" sound, the sensor enters warm-up state, the green indicator light flashes once per second; the green indicator light, indicating that the detector into the normal working condition.
- The detector is equipped with a key, key function: short press on the code, analog alarm; press reset detector.
- The detector detects combustible gas leak after the red light is blinking, while buzzer "bit" alarm sound, alarm box to send an alarm signal, after the exclusion of the combustible gas detector automatically returns to the monitor state, and sends an alarm recovery signal alarm box.
- Yellow lights lit, the buzzer sounding, indicates that the sensor internal fault.
- The detector prolonged use, there will be some oil gas convection window attachment and gas sensitivity, it is recommended once every three months to clean up around the convection window.

 

Smoke Detector

- Design Standard: GB 20517-2006, EN 14604.
- Network alarm: send alarm signals to the alarm box upon detection of smoke.
- Local alarm: =85dB (3m) When detects the smoke ,it will sounder,after smoke exclude, detector automatic recovery;
- The detector can be set to 24-hour zones, when that is disarming, still work.
- A self-test report: can inform the user whether the detector is working properly.
- The detector is equipped with a key, key functions: Testing, Local analog alarm.




Clear Picture 

 





 

 




Packaging & Shipping

 

Shipmet

1, all package can sent by FedEx/DHL/UPS/EMS, based on customer requires.

2, Freight By Sea to Any nearnest port of customer country.

3, Freight by Air to airport of import country.

Paymnet:

 

1. T/T

2. West Union

3. Trade Assurance

4. Paypal 

 

 

Company Information

 

 

 

 

 

Welcome to Visit our Factory!Thanks

 
FAQ




1. Quality of our company.

We are the manufacturer of alarm system for more than 10 years, we are full of experience and technology.

 

2. Quality of our products.

Our engineers who ever worked in a very famous company of alarm system, all the products must be strictly inspected before selling.

 

3. Quality of our services.

 All of our products have a full two-year warranty and low repair rate.

 

4. Quality of our shippment.

 We arrange the shippment as soon as we get the payment, fastly and professionally.

 

5. Quality of our sales representatives.

  Truly, Warmly, Patiently, Professionally.

 

6. Delivery time.

Sample is 1-3 day,bulk order is 8-15 days after confirming.